• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

Replacing a damaged window handle is a relatively simple process and with the right tools it can be done quite quickly. It is essential to know what kind of handle you have and its spindle size before you purchase an alternative.

Older uPVC window handles have a spur which protrudes and locks on the wedge striker for cockspur. They can be left- or right-handed and must be matched when replacing.

What kind of lock or handle do you have? I have

There are many window locks and handles made from upvc, each with its particular advantages and uses. The type of handle that you have will determine if your locking mechanism is efficient and also if it is simple to open windows. With time and regular use, upvc window handles can become damaged or worn out, rendering them less effective and secure. In certain instances, they might even fall completely off. It is important to repair your upvc window handles when you notice they are falling off. This will help avoid burglaries and keep your home safe.

It's a task that virtually anyone can perform. You'll require a few tools, but with right knowledge, it is simple and should only take a few minutes. It is important to be aware of the type cost of windows replacement handle or lock that you have on your window. This will allow you to choose the right glass replacement window.

Inline Espagnolette Handles

These are the most common kind of upvc handle and are typically located on the side of your window. They have a flat design and come with an opening that is connected to the locking mechanism on the window frame when turned. Inline upvc handles also come with a spindle that goes through the center of the handle, and into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have an unusual hook-shaped design. Cockspur handles are held to the frame of the window with a single screw and are less secure than other kinds of window handles.

Handles that can tilt and turn

In contrast to other handles made of upvc that are tilt and turn, these handles can be rotated to open the window, and turned inwards to allow to allow ventilation. They have a 7mm spindle at the back and are available both in right and left-handed versions.

When purchasing replacement handles made of upvc, it is important to verify the length of the spindle because not all handles are identical in size. Drop something in the middle of the hole to measure the length. This is the maximum spindle length that will fit in your window.

What is spindles?

uPVC window handles work similarly as doors. By turning the handle, you are able to open a latch in the frame. The window can then be opened and closed. These handles can be damaged, especially if they're used frequently or subjected to harsh conditions. This can lead to the need to replace your uPVC handles for windows as they might not operate the window in a proper manner in the future.

There are many different kinds of uPVC handles to choose from, comprising Espag, Cockspur and Spaded handle options. These handles are designed to fit in the uPVC frames in a variety of ways, and each type of handle utilizes a specific spindle to secure the mechanism to the window. This is why it is important to know the kind of handle you have on your uPVC window so you can get the correct glass replacement window for it.

The base of the handle will tell you what kind of uPVC it is. There should be a "snap-in cover' over one screw which holds the handle base in the correct position. After removing this you will be able to see the screw that holds the handle base in position. After both screws have been removed, you should be capable of pulling the handle away from the uPVC window.

Once you have removed the uPVC window handle you need to carefully unscrew the spindle you have removed from the locking mechanism. Make note of the length of the spindle as you will need to ensure that you buy an alternative that is the same length as your original handle and locking mechanism.

The main issue with most uPVC window handle problems is that the spindle becomes worn out and can no longer operate the locking mechanism. This could be due wear and tear from continuous use or loosening of the locking mechanism, or even corrosion over time. When this happens it is required to replace the window handle and the locking mechanism to restore complete functionality to your uPVC windows.

How do I take off my old handle?

In the course of time and daily use, window handles may become damaged or broken and if this happens it is essential to fix them as quickly as possible to ensure the safety of your home. It is easy to replace a worn or damaged handle. The task can be completed in under a minute without the need for any special tools.

To remove the handle, first remove the screw at the bottom of the handle. Once the screw is removed, the handle can be removed. There is a second screw that is located at the bottom of the handle's base and this can be removed too. When both screws are removed, the handle can be completely detached from the base of the window.

Once the old handle is removed, take the new handle and align the fixing holes with the holes currently in the window frame. If there is a sticker or cap on the new handle remove it if necessary and then screw the handle in place. It is crucial to verify that the handle works once it is put in place. Turn the handle around and make sure that the lock mechanism is in place.

Espag handles have spindles that protrude out of the handle and slot into the multipoint locking mechanism of the window frame. Cadenza windows feature a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and hook over the outer frame of the window or the transom bar crossmember.

Once you have installed the new handle, slide the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) once the handle is securely fixed. Now that the handle is ready to use, you can open and close the window a couple of times to ensure it works correctly and securely.

How do I put in the new handle?

Changing your uPVC window handle isn't a big deal and the process is actually very simple. All you require is a screwdriver, and a small amount of patience. The first step is make sure that the handle you have previously used is not locked and then take out any screws that are visible, you can also replace these with screw caps if required. After you have removed the handle, you'll need to take note of the length of spindle that extends from the back. This is crucial because it will determine the kind of handle you will need to purchase.

Espagnolette handles on uPVC are the most sought-after kind of handle. The spindle passes through the handle to control the locking mechanism within the window frame. When the handle is turned, it opens the latch on the window, allowing it to open. Over time and through regular use, espagnolette handles can be damaged or destroyed and it is necessary to locate an alternative.

Cadenza handles are another type of uPVC window handle that is commonly used on tilt and turn windows. They have a protruding knife that operates a multiple-point locking mechanism within the window. They are more secure than espagnolette handles since they only open from the inside. They can be replaced using the same procedure as espagnolette handles, however you must ensure that the new handle has a curved blade, as opposed to a flat one.

Once you've decided on the correct handle to purchase, you can simply align the new handle to the existing screw holes, and then screw it in the appropriate position. After that, you can put the screws on and test the new handle. You can perform this by dragging the handle back and forth from the locked position to the unlocked one several times. It might be worthwhile to speak with an expert to determine if you can resolve any issues. They can often advise you on the best approach to solve the issue in a fast and efficient way.